Ghost Controls Keypad & Intercom Repair Nationwide

Ghost Controls Keypad & Intercom Repair: The Miami Owner’s Guide

Ghost Controls keypad and intercom repair in Miami typically runs $185 – $395 installed, and we keep the most common replacement keypads, intercom boards, and weather seals on the truck for same-day fixes in most Miami neighborhoods. Most owners discover the failure the same way: the gate works fine from the remote or the app, but the keypad beeps once and does nothing, or the intercom rings the house but the audio is dead. You’re not imagining it. These parts live outdoors in salt air and afternoon thunderstorms, and Miami weather wears them down faster than the manufacturer’s lifespan estimates suggest.

Call (850) 495-7564

Key Takeaways:

• We stock Ghost Controls-compatible keypads, intercom boards, and power supplies for same-day replacement across Miami.
• Typical installed cost: $185 – $395, with the written price agreed before we start.
• Most keypad failures trace to corroded terminals or a failed membrane, not the control board. We diagnose before we replace anything.
• Every repair carries the 365-Day Done Right Promise in writing.

Which Ghost Controls Models This Applies To

We service the full Ghost Controls lineup we see across Miami: the AXDP, AXP1, TSS1, and the newer GateKeeper series keypads and intercom kits. The compatibility gotcha we run into weekly is this: a Ghost Controls keypad from 2018 is not automatically interchangeable with a 2023 board. Ghost Controls changed the keypad communication protocol on some GateKeeper revisions, so the old keypad will power up and beep but never actually trigger the gate. Check the label on the back of your keypad for the model prefix (AXDP vs TSS1 vs DS1) and the revision number. If the label is sun-faded, which in Miami it usually is, we can read the chip markings or match it by the connector layout.

On the OEM-versus-aftermarket decision for Ghost Controls specifically: we prefer OEM or Ghost Controls-approved replacements for the intercom and any keypad tied to the entry sensor loop. Aftermarket keypads exist, and some are fine for a basic open command. But Ghost Controls boards run a tight voltage tolerance, and a cheap aftermarket keypad can cause phantom opens or drain the battery faster. The savings usually dies inside a Miami rainy season.

Signs Your Ghost Controls Keypad & Intercom Repair Is Failing

Here are the five failure patterns we see most often in Miami, in order from “fix it later this week” to “fix it before Friday.”

• Keypad beeps but the gate does not move. The membrane is sending a digit, but the code chip or the board’s receiver is not matching it. This is the most common Ghost Controls failure we see, and about half the time it is the keypad itself, not the main board.
• Keypad is completely dark, no beep, no backlight. Nine times out of ten this is a corroded wire terminal or a blown fuse on the keypad’s feed line, especially on Miami gates where the keypad sits on the west-facing side and gets afternoon sun and evening rain. The board inside the gate is usually fine.
• Intercom rings the house phone but voice is one-way or dead. On Ghost Controls intercom systems, the audio wire pair is often the first casualty of moisture wicking into the cable jacket. You hear the ring because the ring signal is simple; the voice signal needs a clean pair and fails first.
• Gate opens on its own, or the keypad triggers the gate without a code. A membrane keypad with a stuck button or a corroded trace can send a ghost signal. This is a security problem, not an annoyance, and it needs attention same-day. We treat phantom gate opens as priority work.
• Screen or keys work only when you press hard. The membrane is worn. Keypads in direct Miami sun get cooked, and the conductive layer separates from the circuit sheet. No cleaning fixes that; the part is done.

Replacement Cost & What’s Included

For Ghost Controls keypad and intercom repair in Miami, expect a range of $185 to $395 installed, with most jobs landing around $260 to $310. The range depends mostly on which brain we are replacing: a standalone keypad is on the lower end, a keypad paired with a new intercom board and a fresh power supply runs toward the top. Labor is flat-rated, not hourly, so the written price you get before we start is the price you pay, period. Here is how it typically breaks down.

Every quote includes the part, the labor, the waterproofing re-seal, and testing the full open/close loop. What you approve in writing is what we install. If we open the housing and find a second issue, we stop, call you with a photo, and get your okay before ordering or touching anything else. No surprise line items at the end, ever. The work is covered by our 365-Day Done Right Promise: if the repair fails within a year, the return visit is free.

DIY or Call Us?

What you can safely check yourself: whether the keypad has power (most have a small LED that lights with any key press), whether the terminal screws are tight if you can see them, and whether a breaker tripped inside the gate box. That is about as far as we recommend. Everything past that involves a multimeter, low-voltage wiring, and sometimes a live board with stored charge, and keypads and intercoms tie directly into the board that controls a moving gate. It is not high-tension like a spring, but a wrong wire on a Ghost Controls board can send 12V where it doesn’t belong and turn a $200 keypad job into a $600 board replacement. If your gate is phantom-opening or the intercom is dead, call us at (850) 495-7564 and we’ll send a tech who has seen your exact failure before.

FAQs