Linear Access Control Installation Nationwide

Linear Access Control Installation: The Miami Owner’s Guide

We stock and install Linear access control systems across Miami, with most full installations running $850 to $2,400 depending on what you already have on the gate. The typical job – a new Linear controller, card reader or keypad, and the wiring to make it talk to your operator – lands around $1,200 to $1,600 installed. Here is how owners usually find us: the keypad still beeps but the gate will not open, or the system stopped recognizing cards after a storm rolled through Coral Gables or Kendall, or the previous installer buried a splice that finally corroded through in the humidity. That is the Miami reality. Salt air and afternoon thunderstorms do not just wear out gates. They wear out the brains that run them.

Call (850) 495-7564

If your Linear access control has failed or is failing, call (850) 495-7564 and we will match the right replacement to your exact model before we ever roll a truck.

Which Linear Models This Applies To

We work on the Linear access control lines most common across Miami residential and small commercial gates: the AE-100, AE-200, and AE-500 telephone entry systems, the AM3Plus and APeX series controllers, and the older RE-1 and RE-2 receivers you still find on a lot of 10-to-15-year-old gate setups in neighborhoods like Shenandoah or the Upper East Side. If you are not sure which one you have, open the enclosure and look for the model sticker. Linear puts it on the inside of the cabinet door, not on the circuit board itself. That little detail trips up a lot of people.

One compatibility gotcha worth knowing: the APeX wiring is not a drop-in swap for an AE-100, even though both say “Linear” on the box. The APeX uses a different relay arrangement and a different power draw, so if someone tries to reuse the old wiring without checking gauge and run length, you get a system that works for three weeks and then flakes out. We match parts by model and by wire run. OEM Linear boards are what we install most often, because the firmware and surge tolerance are built for the long haul. When a customer is on a tight budget, we offer quality aftermarket equivalents – but only the ones we have tested on Miami gates and trust. We will tell you the difference up front and let you decide.

Signs Your Linear Access Control Installation Is Failing

Access control failures in Miami do not usually announce themselves. They start small. Here is what we see most often:

• The keypad lights up but the gate stays dead. The relay inside the controller is worn or the trigger wire to the operator has corroded. In Miami, the corrosion is almost always the culprit if the enclosure has any gap at all.
• Cards and fobs work sometimes, not other times. That intermittent behavior is classic antenna or reader degradation. Humidity gets inside the reader housing over a few seasons and the read range shrinks.
• You hear a click at the box but nothing moves. The controller is doing its job. The operator is not. That tells us the problem may be in the wiring between the two, not the Linear board itself – which changes the repair approach entirely.
• The system resets or loses programming after a storm. Linear control boards do not love power surges, and Miami gets them almost daily between June and October. If you have no surge protection on the line, the board takes the hit.
• Some tenants or family members can get in, others cannot. This is almost always a credential or programming issue, not a hardware failure. But it needs a service visit to sort out, because the programming menu on an AE-500 is not something you want to guess through.

Replacement Cost & What’s Included

In Miami, here are the installed price ranges we give for Linear access control installation:

• Controller replacement (AE-100, AE-200, AM3Plus): $850 to $1,400 installed, including the new board, programming, and verification against your existing operator.
• Full keypad and reader installation: $950 to $1,800 depending on wire run length and whether we are pulling new low-voltage line or reusing existing.
• Complete access control package (controller, reader/keypad, power supply, surge protection): $1,600 to $2,400, which is what we recommend when the old system is 10-plus years old and you want one that will outlast the next five hurricane seasons.

What drives the range is the wire run, the condition of the old conduit, and whether your operator is compatible without an extra relay interface. Every quote is a written price agreed to before we start. That is a flat rule. The labor includes programming every credential you hand us, testing the full open-close cycle, and leaving the enclosure sealed against Miami weather. The 365-Day Done Right Promise covers every part and wire we touch. If the repair is not right, the second visit is free.

DIY or Call Us?

This one is a call-us situation. Access control touches line voltage on the power supply side and low-voltage logic on the control side. Wire it wrong, and you can burn out the board the moment power comes back on. We have replaced more than one brand-new board that a homeowner tried to install over a weekend, only to cook the relay because the operator circuit pulled more current than the board was rated for. That is not a judgment, it is just what low-voltage wiring mistakes do.

What you can safely do: note the exact model number, count how many credentials you need programmed, and check whether the enclosure shows any signs of water intrusion. That information saves you money on the visit. Then call (850) 495-7564 and let us handle the wiring, the testing, and the programming. Know what’s broken before we touch it. Fix it once.

FAQs